MENU
#03148
Self-Adhesive cable clamp for WLC 5.5mm cables
This polyamide cable clamp is designed for securing round cables up to 5.5mm in diameter. It ensures easy and aesthetic installation on any surface. It is also ideal for mounting WLC detection cables.
| Technical Specifications | |
|---|---|
| Bundle Diameter | 5.5mm |
| Material | Polyamide |
| Color | Black |
| Flammability Rating | UL94V-2 |
| Dimensions (H x W x L) | 12.2 x 13.4 x 25.8 mm |
#03135
Sensor extension unit (Vutlan VT408)
The VT408D Extension unit increases the number of analog sensors connected to any Vutlan monitoring device. All connected sensors are automatically detected and integrated into the system. CAN devices can be connected in a chain. DIN mounting.
| Number of analog ports |
8, RJ11 6P4C CAN ports |
|---|---|
| Number of CAN ports | 2 |
| Maximum bus length | 225 meters |
| Maximum analog sensor cable length |
50-150 meters, depending on the sensor type |
| Installation | DIN mounting 7mm (0.28in) / 15mm (0.59in) |
| Connection | Can be connected via RJ-12 cable to the CAN input of the control unit or another CAN sensor. The module is automatically detected on the first connection. |
| Set includes |
module, CAN cable RJ-11 (2m), 12VDC power adapter |
| Dimensions (LHW) | 129×56×28,6 mm |
#08288
Sensor unit (Vutlan VT408)
Module allows to increase the number of sensors connected to the Vutlan master module. The expansion unit is connected to the CAN connector of the controller.
| Number of analog ports | 8 |
|---|---|
| Number of CAN ports | 2 |
| Maximum bus length | 225 meters |
| Maximum analog sensor cable length |
50-150 meters, depending on the sensor type |
| Installation | In the lower part of the casing there are Ø 5 mm holes for mounting the module, |
| at a distance of 50 mm and 89 mm from the center. The cable is connected to the connector on the side wall. | |
| Connection | Can be connected via RJ-12 cable to the CAN input of the control unit or another CAN sensor. The module is automatically detected on the first connection. |
| Set includes |
module, CAN cable RJ-12 (2m), 3.5x16mm screws |
| Net weight | 0.6 kg |
| Dimensions (LHW) | 110×68×40 mm |
#08204
USB100 / USB dome camera
USB UVC/MJPEG digital camera with high resolution and with IR Leds for direct connection to the VUTLAN system controller.
It allows to view the monitored room on an ongoing basis as well as send a video sequence to an email address in response to a defined event.
In addition, the camera connected to the VUTLAN controller is visible in the network at a dedicated URL, allowing to capture the video stream just like from an IP camera (MJPEG stream).
It allows to view the monitored room on an ongoing basis as well as send a video sequence to an email address in response to a defined event.
In addition, the camera connected to the VUTLAN controller is visible in the network at a dedicated URL, allowing to capture the video stream just like from an IP camera (MJPEG stream).
| HARDWARE FEATURES: | |
|---|---|
| Interface | USB format(Complies with USB 2.0 |
| CAMERA: | |
| Image Sensor | 1/4" Color CMOS H62 |
| Resolution | 1.0 Megapixel (640 x 480) |
| Minimum Illumination | 0.01 Lux @ F1.2 |
| VIDEO/IMAGE: | |
| Video Compression | MJPEG |
| Frame Rate & Resolutions |
Max. 20 fps at 640x480 (VGA), Max. 20 fps at 320x240 (QVGA) |
| Video Streaming | Controllable Frame Rate |
| OTHERS: | |
| Cable lenght | 5m |
| Operating Temperature | 0°C∼ 40°C (Humidity 0% RH∼ 80% RH) |
| Weight | 550g |
#03128
VT-BAT / Reservation battery 9V
"VT-BAT / Reservation battery 9V" keeps the device operational while the main power source is disabled. The device uses a non-rechargeable 6F22 9V lithium battery. The Vutlan monitoring system may work from this battery for approximately 1 to 10 hours.
A 9V is not included. You can use a 9V battery enclosed in a standard PP3 enclosure.
A 9V is not included. You can use a 9V battery enclosed in a standard PP3 enclosure.
#03136
VT12 Relay Module (Vutlan VT12)
- 12V DC Power max 0.5A
- Relay output max 5A.
- Ground (GND)
VT12 Relay Module is a dual-channel switching unit designed to turn on/off loads. It can be connected to the dry contacts outputs of VT855 and VT336 Vutlan monitoring units to turn on/off loads with current up to 1A, when the device's Dry contact output is triggered.
Dry Contact Inputs (A and B): Dual Outputs (A and B): Each output provides:
VT11 can be used separately with third-party controllers.
| Technical specifications | |
|---|---|
| Power terminals |
2 outputs (A and B)(Relay, Ground, 12V) |
| Maximum direct current | 0,5A |
| Relay Output | 5A |
| Power input terminal |
2P, pitch 3.5 mm, 12V DC |
| Dry contact inputs |
2 inputs (A and B), 4P, pitch 3.5 mm |
| Features | |
| Mounting possibilities | DIN Rail |
| Max distance | 100m |
| Power Consumption | 200mW |
| Operating temperature | Min. -40° C - Max.+85° C |
| Package includes |
relay module, power supply 12VDC 1A |
#03106
VT122i / 19" holder (for VT335t)
Holder / bracket for VT335t monitoring unit #03113 (and older VT355i) . 1U rack mount, 19".
#03119
VT125t / 19" holder (for 2x VT408)
Holder / bracket for x2 pcs of VT408 / Sensor extension units. 1U rack mount, 19".
#03121
VT485r / OSDPv2 Reader Extension
Allows to connect readers, and keypads with OSDP protocol support. It is an extension PCB board and should be purchased separately.
It can be used with VT335t, VT825t, and VT855t monitoring systems. VT485r can be inserted inside the monitoring unit while the unit is in operation. VT485r has internal termination and by default, it is switched ON (if required can be turned Off).
Allows to connect SE mini reader, SE keypad, and any other 3rd party OSDP readers or keypads.
It can be used with VT335t, VT825t, and VT855t monitoring systems. VT485r can be inserted inside the monitoring unit while the unit is in operation. VT485r has internal termination and by default, it is switched ON (if required can be turned Off).
Allows to connect SE mini reader, SE keypad, and any other 3rd party OSDP readers or keypads.
Page 6 of 7
|
